Log Download
Ok yes you where right. I formatted the microsd card and I can now see and download in MP... I should have tried that but because APM could read it I assumed it was something else. My little crash was...
View ArticlePixhawk Crash in Mid-air after flying stably
I have also put together a crash report doc - https://drive.google.com/open?id=0B2IbWlGU-rXkUDRGSEpZcFd2UjA
View ArticleAPM 2.6 No output to LEDs on Aux pins
I checked the documentation for APM 2.6 and see that these pins can be set as relay pins or output pins. It also looks like there needs to be firmware to support that output which I am not familiar...
View ArticlePixhawk Crash in Mid-air after flying stably
Sync issues are caused by low RPM motors with large props that are told to change speed very rapidly. The motors are not able to keep up with the speed change and lock or stop. To help prevent this...
View ArticlePixhawk Crash in Mid-air after flying stably
Thanks Mike. We were using 14 inch wooden propellers with the Kongcopter FQ700 frame. The 40 Amp NO BEC AIR ESCs and 380 kv 4006 antigravity T-motors. Could this combination result in an ESC/motor...
View ArticleGForces were they are located?
Thank you for your fast reply!That is perfect I can now see the g forces on HUD.One more question please.Is it possible to create tlog files from bin files?I want to have just the APM pilot on the...
View ArticleUnread post MP Voltage not dropping as battery voltage drops
Thanks Paul, I've ended up buying a 3DR Power Module (all-be-it a clone as I couldn't find a 3DR one in stock anywhere in the UK). I now have full volts and current readouts. The voltage I WAS seeing...
View ArticleClik here to view.
Proposal for companion system architecture
SystemsArchitectureCompanionComputerRev21.jpg960x720 88.6 KB This is the latest revision of the Companion Computer Architecture.After some more discussion regarding the overall structure, we thought...
View ArticleUbuntu not recognizing Pixhawk
I have added my account to the dial out group. The sd card is the one it came with I have done nothing to it. It was in the board when I got it It took it out making sure it was there then put it...
View ArticleGPS has not been fully configured
This issue is on a second drone as well. So far every plane I have put 3.5.2 on has this issue.
View ArticleHKPilot32 immediately disarmes
Please watch the attached (WeTransfer) video, does anyone know how I can fix this? My first thought was that the ESC wasn't good, so I've set up another (with a working BEC for the Servos). As you can...
View ArticleGForces were they are located?
please look at control-f > osdvideo it does something like this, this only supports tlogs though
View ArticleMission Planner on Raspberry Pi
HiI get error messages saying "cannot access memory at address 0x1" +++ Any idea what the problem is ?
View ArticleConnecting Pixfalcon outputs to servos and ESC
Thank you Thomas! Afirmative, hobbyking. I miss some extra manuals.Is there any problem if I use the powermodule? It has some extra outputs. My ESC is covered. There is cable from ESC to the pixfalcon...
View ArticleQuadplane can't arm---V3.5
There is a parameter SCHED_LOOP_RATE in the advanced parameter list. You should raise that to 300.For details please see:http://ardupilot.org/plane/docs/quadplane-support.html#parameter-setup
View ArticleСhute setting AP_PARACHUTE_RELEASE_DELAY_MS
It is normal for a servo release to not be permanent. Does your parachute need it to be permanently open to work? If so, can you describe the mechanism you have?
View ArticleСhute setting AP_PARACHUTE_RELEASE_DELAY_MS
hi,my parachute mechanism is normal,nothing special.! I just want it to be more secure,in case the wind or the parachute slowly dropping from the capsule;Or can I extend the deploy time?
View ArticleClik here to view.
Qplane(v3.5) ,mode Qhover to Qloiter translation not stable
At first I fly my quadplane in FBWA mode,and then I slow down my plane and then change to Qhover mode, it acts well . I control the plane in Qhover mode until the plane stabe,without horizontal...
View Article